How To Choose The Appropriate Cleaning Agent For Industrial Floor Scrubbers When Cleaning Oil Stains?

Dec 05, 2025

Leave a message

How to choose the appropriate cleaning agent for industrial floor scrubbers when cleaning oil stains?

 

The oil-removal capability of industrial floor scrubbers is closely related to the choice of cleaning agent. In machining workshops, greasy marks may remain on the ground even after repeated cleaning. In auto repair shops, oil stains mixed with sediment can form hardened lumps that ordinary cleaning agents cannot dissolve. Many factories have encountered this dilemma: the performance of the floor scrubber is not the problem-choosing the wrong cleaning agent results in twice the effort for only half the effect.

news-225-225

The cleaning performance of industrial floor scrubbers on oily floors depends 50% on equipment performance and 50% on the "precise matching" of cleaning agents and oil stains. Choosing the right cleaning agent can triple the efficiency of oil removal and also extend equipment lifespan; choosing the wrong one can leave oil residue, corrode the equipment, and even pose safety hazards. Below, we explain how to choose the appropriate cleaning agent for handling oil contamination through a few key steps.


 

1. Identify Oil Stains First: Different types of oil stains require different cleaning logic

 

Oil contamination in industrial environments is complex and can be divided into three categories based on composition and adhesion state.

Cleaning difficulty and the required cleaning agent are completely different. Using one product for all types will only be ineffective.

 

1. Light to moderate oil stains: soluble "liquid oil film"

 

These stains mostly come from light oils such as lubricating oil and hydraulic oil, forming a thin oil film on the floor. They are commonly found in electronics assembly workshops and equipment lubrication areas.
Characteristics: weak adhesion, not mixed with dust or metal shavings, and removable with general-purpose cleaning agents.

A CleanHorse customer in Mexico once used water alone with a floor scrubber to clean this kind of oil stain. Although the surface oil film was temporarily removed, the oil seeped out again after one hour, and the floor returned to a greasy state. This is a "temporary solution" caused by using a non-targeted cleaning method.

 

2. Heavy mixed oil stains: hardened oil sludge that is difficult to remove

In auto repair shops and machining workshops, oil stains may mix with metal debris and cement dust, forming hardened sludge after exposure to heat. This type of oil stain has extremely strong adhesion, and ordinary cleaning agents cannot penetrate it. Specialized products containing strong penetrating components are required.

One auto repair shop mistakenly used household dishwashing detergent to clean such stains. It not only had no effect but also caused the floor scrubber's rubber squeegee to age and crack, resulting in nearly 1,000 yuan in replacement costs.

 

3. Special oil stains: "corrosive oils" with safety risks

Mold-release oils in chemical workshops and animal or vegetable oils in food factories fall into this category. The former may contain corrosive components, and the latter is prone to bacterial growth. Cleaning these stains requires both oil removal and compliance with industry-specific safety standards-for example, using food-grade cleaning agents in food factories to avoid chemical residue contamination.

Small Body, Big Achievements: The Application Value Of Small And Compact Ride-On Floor Scrubbers


 

2. Core Principles: Three checks and one match, so you choose correctly without mistakes

 

Selecting industrial floor-cleaning agents should follow the principles of checking the type of oil stain, checking the floor material, checking environmental requirements, and matching the cleaning agent to the floor scrubber. All four dimensions are essential.

 

1. Check the type of oil stain: choose appropriate ingredients

For light to moderate oil stains, choose neutral surfactant cleaning agents. Components such as alkyl glycosides can quickly break down oil films and are non-corrosive to equipment.

For heavy mixed oil stains, use alkaline cleaners with a pH of 10–12, containing ingredients such as sodium hydroxide and sodium carbonate. These soften sludge through chemical reactions, enabling thorough removal with the brush pressure of a floor scrubber.

For special oil stains, choose targeted solutions-for example, food-grade citric acid cleaners for food factories and corrosion-resistant cleaners for chemical plants.

 

2. Check the floor material: avoid floor damage

Epoxy and marble floors must not use strong alkaline cleaners (pH > 12), as they will corrode the surface gloss. Neutral or mildly alkaline products (pH 7–9) are recommended.

Cement and diamond-sand floors are highly resistant and can use strong alkaline cleaners to improve oil removal efficiency.

Wooden floors require specialized wood-floor cleaners to prevent moisture absorption and deformation.

A furniture factory once used a strong alkaline cleaner on its workshop's wooden floor, causing the flooring to warp. Repair costs exceeded 10,000 yuan-an expensive lesson.

 

3. Check environmental compliance: meet industry standards

 

Factories in Europe and the U.S. must check whether cleaning agents have REACH certification.

Food factories must use FDA-certified, food-grade cleaning agents to ensure no residue.

Chemical and electronics plants should use low-VOC products that meet environmental requirements.

Although phosphorus-containing cleaners remove oil effectively, they pollute water systems and are banned in most industrial environments.

 

4. Match the floor scrubber: maximize equipment efficiency

Hand-push scrubbers with small tanks should use highly concentrated cleaning agents (dilution 1:100) to reduce refilling frequency.

Ride-on scrubbers can use automatic proportioning systems with large cleaning-agent containers for precise dosing.

Scrubbers with heating functions should be paired with high-temperature-resistant cleaners (over 60°C). Heating can increase oil-removal efficiency by up to 40%, especially useful in winter.


 

3. Practical Tips: Dosage, dilution, and usage precautions

 

Choosing the right cleaning agent is only the first step-correct use is equally important. Incorrect dilution or improper usage may reduce cleaning effectiveness or damage the machine.

 

1. Accurate dilution

Light to moderate oil stains: 1:80–1:100

Heavy oil stains: 1:30–1:50

Always test on a small area before cleaning a large floor.

One machining factory used undiluted cleaner directly in an attempt to remove oil quickly. It corroded the scrubber motor's sealing ring, causing water leakage, and repairs cost more than 2,000 yuan.

 

2. Use at the right time

Clean oil stains before they dry, as they have not yet solidified and cleaning agents can penetrate more easily.

For hardened sludge, spray diluted cleaning agent, let it soak for 10 minutes, and then scrub for better results.

 

3. Maintain the equipment

After cleaning, rinse the scrubber's tank and pipes with clean water to prevent chemical residue from corroding the machine.

Clean the brush plate and squeegee weekly using a dedicated cleaner to prevent oil buildup and ensure optimal performance.

CleanHorse M10 Hand Push Floor Scrubber: Small Size, High Power, Efficient For Narrow Spaces


 

Conclusion: Cleaning agents are the "best partner" for floor scrubbers

 

Using an industrial floor scrubber alone is not enough. Operators also need to understand maintenance habits, environmental conditions, and basic troubleshooting.

 

Choosing the right cleaning agent represents half the success of cleaning oily floors.
By identifying the type of oil stain, selecting a product suited to the floor material and environmental standards, matching it with the scrubber, and using it properly, factories can achieve:

efficient oil removal

equipment protection

environmental compliance

Instead of blindly trying different products, factories should conduct simple preliminary research. By doing so, cleaning agents can become the scrubber's "capable assistant," helping completely eliminate oil-cleaning problems.

Send Inquiry