How to Replace the Water Absorbing Rubber Strip of a Floor Scrubber
The water absorbing rubber strip of a floor scrubber is a common consumable that needs to be replaced regularly.
For first-time buyers and users, learning how to replace the strip is a basic skill.
In fact, the process is simpler than many imagine-most scrubbers use either "snap-on" or "screw-fixed" strips, which only require a screwdriver and can be replaced in less than 10 minutes.
To help users better understand, we'll break the process into steps. These are general instructions (details may vary depending on the brand and model, so always refer to the equipment manual first).
Step 1: Remove the Old Rubber Strip and Clean the Suction Scraper
Park and power off the machine
Place the scrubber on a flat surface, turn off the power, and unplug the battery model if applicable. Safety first.
Lift the suction scraper
Use the "up/down switch" (usually at the back of the device, labeled "Up/Down") to raise the scraper to its highest position, preventing it from touching the ground during disassembly.
Remove the old strip
Buckle type: Pinch the buckles at both ends of the strip (or press the side release button) and gently pull it outward. Scrubbers usually have both a front and a rear strip, which should be removed together.
Screw-fixed type: Use a Phillips screwdriver to loosen (not fully remove) the 2–3 screws on each side, then slide out the old strip.
Clean the suction scraper
Use a brush or damp cloth to remove mud, hair, and debris, especially in the strip groove. If rust is present, apply a small amount of anti-rust oil, as rust can affect the strip's adhesion and water absorption performance.

Step 2: Install the New Rubber Strip (Check Direction and Fit)
When installing a new strip, the direction is crucial. Installing it backwards can reduce absorption efficiency by more than 50%.
Confirm the direction
Some strips have an arrow mark (pointing in the cleaning direction) or a text mark (e.g., "Front").
If unlabeled, check the cross-section: the thinner side should face the floor, the thicker side should face inward.
Insert into the slot
Buckle type: Align both ends with the slot and push in until you hear a "click."
Screw-fixed type: Align symmetrically on both sides, then tighten the screws with moderate force (avoid over-tightening, which can damage the strip).
Check the fit
Press the middle of the strip to confirm full contact with the bracket (no gaps). Lower the scraper so the strip touches the floor-it should bend slightly (about 5°). Adjust the scraper height if necessary.
Step 3: Test and Fine-Tune
After installation, testing ensures correct placement and full performance.
No-load test
Start the scrubber without water, run the suction motor for 30 seconds, and check whether the strip rubs excessively against the floor. If you hear a harsh "sizzling" sound, adjust the position.
Load test
Pour a small amount of water on the floor and scrub 1–2 meters. Check for water marks or leaks. If marks remain, the strip may be misaligned or the scraper height may need adjustment (lower by 1–2 mm using the adjustment knob).
👉 Tip: To fine-tune, loosen the scraper screws and slightly adjust the height of the strip up or down until the best absorption effect is achieved.

Step 4: Choose the Right Rubber Strip Material for Different Scenarios
The ground environment and type of stains greatly affect strip performance. Choosing the right material can extend service life.
General use: Nitrile rubber (cost-effective)
Scenarios: Shopping malls, offices, schools (ceramic, marble, epoxy floors) with mainly dust and water stains.
Features: Good elasticity, mild oil resistance, affordable ($50–80 each).
Caution: Avoid sharp debris or very low temperatures (below -5°C), which cause hardening.
Heavy-duty use: Polyurethane (high wear resistance)
Scenarios: Factories, warehouses, construction sites (cement, rough surfaces, oil, metal debris).
Features: 2–3× more wear-resistant than nitrile, high hardness, strong oil resistance, long-lasting.
Downside: Lower elasticity, requires scraper height adjustment. Price: $80–120 each.
Special environments: Low-temperature/moisture-resistant rubber
Cold regions (e.g., Northern Europe, Canada winters below -10°C): Choose EPDM rubber, elastic down to -30°C.
Humid regions (e.g., Southeast Asia, food workshops): Choose anti-mold strips with protective coating to prevent odor and decay.

Conclusion
Although rubber strips are simple consumables, they play a vital role in cleaning efficiency.
The cost is very low (one strip equals just 0.5%–1% of the equipment price), but neglecting replacement can lead to:
Rework: repeating cleaning due to poor absorption.
Safety risks: slippery floors from residual water.
Equipment damage: sewage seeping into internal components.
By following the three-step judgment method and choosing suitable materials, you can ensure optimal cleaning results and extend the overall lifespan of your floor scrubber.
If unsure about which strip material to use, share your usage scenario (e.g., "supermarket tile floor, 6 hours/day") with your supplier-they can recommend the most suitable type and often provide installation guidance for worry-free replacement.
